Sound system for Seat Leon 5F (Beats, with fibre optic cable) DSP amplifier + subwoofer replacement kit | V1 | Plug & Play | OPTION
€699.00*
Prices incl. VAT plus shipping costs
Delivery time: 2-3 days ***
free shipping **
Seat Leon 5F with Beats sound system (with fibre optics) | DSP sound system incl. subwoofer replacement kit | V1 | OPTION
The ultimate sound boost for your Seat Leon 5F with pre-installed Beats sound system
ATTENTION: This set is only suitable if fibre optic cables are connected to your BEATS power amplifier (marked red).
If your power amplifier does not have a fibre optic cable , you will need this set.

ATTENTION: Thanks to the new, revised wiring harness, installation is now possible, contrary to our YouTube video!
Compact DSP power amplifier: increased performance with simple installation
The very compact 6-channel power amplifier is a real powerhouse and can be integrated in no time at all via plug & play thanks to the cable set included in the scope of delivery. This allows you to experience an unrivalled sound upgrade, with sound and bass coming into their own. The power amplifier emits hardly any heat and can therefore be concealed behind the dashboard, for example.
Ready to go immediately
The appropriate sound setup is already pre-installed in the integrated sound processor. You can make fine adjustments to the power amplifier in just a few simple steps. For a detailed explanation, simply watch our YouTube video.
Subwoofer replacement for powerful bass
The original Beats subwoofer is replaced by our powerful model. You will experience a significant increase in the bass range, which can also be more intense if desired. We recommend the V2 set for bass lovers who want the bass to be a little more dominant.
Simple installation thanks to Plug & Play
Installation is simple and can be done by anyone thanks to our YouTube video. A vehicle-specific wiring harness makes your work much easier. No cutting of cables, no time-consuming installation work!
Support and customer service
If you have any questions or problems, our support team is always available. Simply contact us by e-mail or telephone.
Scope of delivery:
- OPTION DSP6 power amplifier
- 6" subwoofer incl. mounting ring and installation accessories
- Plug & Play cable set between car radio and vehicle (incl. power supply)
Accessories:
Helpful (installation) accessories can be found next to the item description or at the bottom of the page in the "Accessories" tab.
Technical data DSP power amplifier
- Highly efficient 6-channel DSP amplifier
- Class GD
- 6-channel amplifier / 8-channel DSP
- 6 x 60 watts RMS (4 ohms)
- 4 x 60 watts RMS (4 ohms) + 1 x 120 watts RMS (4 or 2 ohms)
- Channels 5 and 6 are combined in mono mode
- Minimum impedance on all stereo channels: (3 Ohm)
- Minimum impedance in mono mode: 1.5 Ohm
- ADEP.3 diagnostic protection for problem-free connection to OEM radios
- Start/stop capable up to 5 sec. up to 6 volts
- High-level in (4 channels) with automatic on/off switch
- Frequency band: 20 Hz to 21k Hz
- Integrated 8-channel DSP processor with 358 kHz
- 2 channels line-out up to 3 Volt | 3.5mm jack
- 2 phase synchronous DC/DC converter
- A/D converter: BurrBrown
- D/A Converter: BurrBrown
- Operating voltage: 10.3 V - 17.5 V
- Power reduction to mid-power mode
- Minimised Dimensions for uncomplicated retrofitting
- 94 x 149 mm x 32 mm (118 x 149 mm with mounting bracket)
- 0.6 mA standby quiescent current
- Main connection: 20-pin Molex MiniFit Jr.
- Subwoofer connection: 4-pin Molex MiniFit Jr.
- Programming port for DSP-Eprom: RJ-45 modular jack
- Remote control connection: RJ-45 modular jack
- Power and Protect LED
Technical data subwoofer
- Impedance: 4 + 4 Ohm
- Die-cast aluminium basket
- Poly-carbon cone
- Ventilated centre spider
- Ultra low bass technology
- Pe 125/250 Watt power handling