Sound system for Mercedes V-Class W447 | DSP power amplifier + subwoofer + front and rear speakers | V3 | OPTION

Plug & Play DSP amplifier + subwoofer + front & rear speakers incl. insulation | V3

This V3 set takes your Mercedes V-Class 447 (1st facelift, model year 2019-2024) to a whole new sound level.

It combines the compact OPTION DSP-6 amplifier with vehicle-specific DSP setup, a passive under-seat subwoofer, the high-quality front speaker kit incl. insulation and the rear speaker kit for the rear side panelling incl. insulation and tools.

The result: an all-round impressive sound system - with powerful bass, clear highs, rich mids and even sound distribution throughout the vehicle. Thanks to complete plug & play installation, the original wiring remains untouched and everything can be retrofitted at any time.

Installation:

The installation is completely plug & play - no original cables are damaged. The enclosed T-cable set is connected directly to the factory radio.

• Remove the ventilation grille with the enclosed pull-out hook and loosen the Torx screws behind it.
• Pull out the radio and insert the T-cable set in between - all plugs remain undamaged.
• Securely fasten the DSP-6 power amplifier under the centre console using wide Velcro tape.
• Route the subwoofer cable to under the driver's seat, insert the subwoofer using an E14 socket spanner and 40 mm angle Torx and secure with metal brackets.
• Install the front loudspeakers: Replace the original speakers with the new 16.5 cm woofers, simply clip the new tweeters onto the original grilles and connect using Plug & Play.
• Front insulation: 3x aluminium butyl for door panels, 1x foam mat for decoupling, 1m bitumen tape for small parts - all included in the set.
• Install rear loudspeaker: Unclip panelling, insert 16.5 cm woofer and 25 mm tweeter, connect everything via plug & play. Insulation with 2x aluminium butyl and 1x foam mat provides additional sound gain.

With the enclosed remover tool and Torx kit, the door and side panelling can be removed without scratching or damage. Thanks to plug & play technology, the entire set is also suitable for leasing.

Installation video:

Support:

With the help of our YouTube videos, you can carry out the installation yourself in a relaxed manner.

If you have any problems during installation or with the product, you are welcome to contact our customer service team by email or phone. The contact details and times can be found at the bottom right of this homepage.

Scope of delivery:

• OPTION DSP-6 amplifier with vehicle-specific setup
• Underseat subwoofer for Mercedes Vito / V-Class W447 (OPTION | AIR-8 D4)
• 2x 16.5 cm front woofers (plug & play)
• 2x 28 mm front tweeter incl. crossover
• 3x aluminium butyl insulating mat (front doors)
• 1x foam mat (front doors)
• 1m bitumen tape
• Foam sealing rings for speakers
• 2x 16.5 cm rear bass-midrange drivers (Plug & Play)
• 2x 25 mm rear fabric tweeter incl. crossover
• 2x aluminium butyl damping mats (rear area)
• 1x insulating foam mat (rear area)
• 1x Remover Tool
• 1x Torx kit
• 1x wide Velcro tape for fastening
• 1x T-cable set for signal tap on the factory radio (051.060-0)
• 1x subwoofer cable (052.003-0)
• 1x Pull-out hook for ventilation grille
• 1x E14 socket spanner
• 1x 40mm angle torx
• 1x cable tie

Accessories:

Linked (installation) accessories can be found to the right of the item description or in the "Accessories" tab.

Technical data:

• DSP-6 power amplifier:
• 6-channel amplifier with DSP
• Power: 6 x 60 watts RMS
• Auto Sense - automatic switch-on function
• Pre-programmed for specific vehicles - no setup necessary
• Plug & Play - no cables are damaged
• Compact design - ideal for concealed installation

• Subwoofer:
• Chassis: OPTION | AIR-8 D4
• Diameter: 20 cm (8 inch)
• Power handling (RMS): 200 watts
• Impedance: 2 Ohm
• Installation depth: 7.6 cm
• Magnet: Ferrite
• Position: under driver's seat (depending on model, without additional battery)

• Front loudspeaker:
• System: 2-way component system
• Diameter woofer: 16.5 cm
• Tweeter: 28 mm fabric tweeter
• Power handling (RMS): 50 watts
• Impedance: 3 Ohm
• Installation: Plug & Play

• Rear loudspeaker:
• System: 2-way component system for side panelling
• Chassis diameter: 16.5 cm
• Tweeter: 25 mm fabric tweeter
• Power handling (RMS): 50 watts
• Impedance: 3 Ohm
• Installation: Plug & Play