Sound system for Fiat Ducato 9 | V2 | DSP amplifier, speakers + ROCK-1 subwoofer | OPTION
€1,099.00*
Prices incl. VAT plus shipping costs
ready for dispatch immediately, delivery time 1-2 days ***
free shipping **
Fiat Ducato 9 | Sound system V2 | Speakers, subwoofer + DSP power amplifier | Plug & Play | OPTION
The sound in your motorhome is unbearable and you finally want to enjoy really good sound while travelling? Then this complete set for your Fiat Ducato 9 with radio preparation ex works is just right for you.
With this set, you can replace the front speakers and install a subwoofer under the seat. The ultra-compact DSP power amplifier DSP6 provides sufficient power. You can easily and quickly integrate it into your camper with the cable set included in the scope of delivery and enjoy your sound upgrade in no time at all. And best of all: the complete installation is plug & play.
The 6-channel power amplifier provides your front system and the Rock-1 subwoofer with sufficient power so that you can now utilise the full potential in terms of sound, bass and level. Due to the digital design, the power amplifier emits hardly any heat and can therefore be installed invisibly in the radio slot. The passive under-seat subwoofer can be installed in the Fiat Ducato 9 directly and flush under the seat, provided there is no second battery installed.
This sound system is a direct fit if you have installed an aftermarket radio with ISO connection.
If you have installed a FIAT radio ex works, you will also need the following adapter for installation:
If you have installed the 10-inch U-Connect radio, you will need this complete kit instead:
Here you can find the installation video for the sound upgrade for the Ducato 9:
Scope of delivery
- 1x OPTION DSP6 power amplifier
- 1x OPTION Ducato loudspeaker
- 1x Rock-1 (4.3 kg)
- 1x cable set for plug & play installation incl. cable for power supply
- 1x Remover tools
- 4x aluminium butyl insulation mat & 1x optional foam mat
- 1x mounting material
- 1x manual
DSP6 | Ultra compact Class HD DSP amplifier
The 6-channel power amplifier provides your front system and an optional subwoofer with sufficient power so that you can now utilise the full potential in terms of sound, bass and level. Due to the digital design, the power amplifier emits hardly any heat and can therefore be installed invisibly in the radio slot.
Two channels are used for the front system, while two additional channels are available for the rear speakers and a passive subwoofer. Two further channels are then available via the Line Out connection to connect additional active subwoofers or power amplifiers and control them via the DSP.
Technical data DSP6:
- Highly efficient 6-channel DSP amplifier
- Class GD
- 6-channel amplifier / 8-channel DSP
- 6 x 60 watts RMS (4 ohms)
- 4 x 60 watts RMS (4 ohms) + 1 x 120 watts RMS (2 ohms) Monomode switchable
- Channels 5 and 6 are operated in stereo mode as standard
- Minimum impedance on all stereo channels: (3 Ohm)
- Minimum impedance in mono mode: 1.5 Ohm
- ADEP.3 diagnostic protection for problem-free connection to OEM radios
- Start/stop capable up to 5 sec. up to 6 volts
- High-level in (4 channels) with automatic on/off switch
- Frequency band: 20 Hz to 21k Hz
- Integrated 8-channel DSP processor with 358 kHz
- 2 channels line-out up to 3 Volt | 3.5mm jack
- 2 phase synchronous DC/DC converter
- A/D converter: BurrBrown
- D/A Converter: BurrBrown
- Operating voltage: 10.3 V - 17.5 V
- Power reduction to mid-power mode
- Minimised Dimensions for uncomplicated retrofitting
- 94 x 149 mm x 32 mm (118 x 149 mm with mounting bracket)
- 0.6 mA standby quiescent current
- Main connection: 20-pin Molex MiniFit Jr.
- Subwoofer connection: 4-pole Molex MiniFit Jr.
- Programming port for DSP-Eprom: RJ-45 modular jack
- Remote control connection: RJ-45 modular jack
- Power and Protect LED
Zubehör
ready for dispatch immediately, delivery time 1-2 days ***
free shipping **