Sound system for Fiat Ducato 9 | V1 | DSP amplifier + ROCK-1 subwoofer | OPTION

Fiat Ducato 9 | Sound system V1 | Subwoofer + DSP amplifier | Plug & Play | Option

If you also want to improve the sound in your camper in a simple but noticeable way, have already retrofitted the speakers and now want to take the next step, then this set for your Fiat Ducato Series 9 with radio preparation ex works is just right for you.

The incredibly compact power amplifier can be easily and quickly integrated into your camper via plug & play using the cable set included in the scope of delivery and you can enjoy your sound upgrade in no time at all. The 6-channel power amplifier provides your front system and the Rock-1 subwoofer with sufficient power so that you can now utilise the full potential in terms of sound, bass and level. Due to the digital design, the power amplifier emits hardly any heat and can therefore be installed invisibly in the radio slot.

The passive under-seat subwoofer can be installed in the Fiat Ducato Series 9 directly and flush under the seat, provided there is no second battery installed.

This sound system is a direct fit if you have installed an aftermarket radio with ISO connection.

If you have installed a FIAT radio ex works, you will also need the following adapter for installation:

• In the Ducato Series 9

If you have installed the 10-inch U-Connect radio, you will need this complete kit instead:

• In the Ducato Series 9 with 10-inch U-Connnect radio

Two channels are assigned to the front system, while two further channels are available for the rear speakers and a passive subwoofer. Two further channels are then available via the Line Out connection to connect additional active subwoofers or power amplifiers and control them via the DSP.

Scope of delivery

• 1x OPTION DSP6 power amplifier
• 1x Rock-1 subwoofer (4.3 kg)
• 1x cable set for plug & play installation incl. cable for power supply
• 1x mounting material
• 1x manual

DSP6 | Ultra compact Class HD DSP amplifier

The 6-channel power amplifier provides your front system and an optional subwoofer with sufficient power so that you can now utilise the full potential in terms of sound, bass and level. Due to the digital design, the power amplifier emits hardly any heat and can therefore be installed invisibly in the radio slot.

Two channels are used for the front system, while two additional channels are available for the rear speakers and a passive subwoofer. Two further channels are then available via the Line Out connection to connect additional active subwoofers or power amplifiers and control them via the DSP.

Technical data DSP6:

• Highly efficient 6-channel DSP amplifier
• Class GD
• 6-channel amplifier / 8-channel DSP
• 6 x 60 watts RMS (4 ohms)
• 4 x 60 watts RMS (4 ohms) + 1 x 120 watts RMS (2 ohms mono mode switchable)
• Channels 5 and 6 are used for subwoofers in stereo mode
• Minimum impedance on all stereo channels: (3 Ohm)
• Minimum impedance in mono mode: 1.5 Ohm
• ADEP.3 diagnostic protection for problem-free connection to OEM radios
• Start/stop capable up to 5 sec. up to 6 volts
• High-level in (4 channels) with automatic on/off switch
• Frequency band: 20 Hz to 21k Hz
• Integrated 8-channel DSP processor with 358 kHz
• 2 channels line-out up to 3 Volt | 3.5mm jack
• 2 phase synchronous DC/DC converter
• A/D converter: BurrBrown
• D/A Converter: BurrBrown
• Operating voltage: 10.3 V - 17.5 V
• Power reduction to mid-power mode
• Minimised Dimensions for uncomplicated retrofitting
• 94 x 149 mm x 32 mm (118 x 149 mm with mounting bracket)
• 0.6 mA standby quiescent current
• Main connection: 20-pin Molex MiniFit Jr.
• Subwoofer connection: 4-pole Molex MiniFit Jr.
• Programming port for DSP-Eprom: RJ-45 modular jack
• Remote control connection: RJ-45 modular jack
• Power and Protect LED

Rock subwoofer manual PDF download

Manual DSP6 power amplifier PDF-Download