Sound system for Citroen Jumper | V2 | DSP power amplifier + ROCK-2 subwoofer + speakers | OPTION
€1,099.00*
Prices incl. VAT plus shipping costs
Delivery time: 2-3 days ***
free shipping **
Citroen Jumper | Sound system V2 Rock-2 | Speakers, subwoofer + DSP power amplifier | Option
The sound in your motorhome is unbearable and you finally want to enjoy really good sound while travelling? Every centimetre is completely planned and you don't quite know where to put a subwoofer? Then this complete set for your Citroen Jumper with radio preparation ex works is just right for you.
With this set, you can replace the front speakers and install a subwoofer between the front seats. The ultra-compact DSP power amplifier DSP6 provides sufficient power. You can easily and quickly integrate it into your camper with the included cable set and enjoy your sound upgrade in no time at all. And best of all: the complete installation is plug & play.
The 6-channel power amplifier provides your front system and the Rock-2 subwoofer with sufficient power so that you can now utilise the full potential in terms of sound, bass and level. Due to the digital design, the power amplifier emits hardly any heat and can therefore be installed invisibly in the radio slot. The passive subwoofer can be installed in the Citroen Jumper flush with the front seats.
The cable kit in this sound upgrade is designed for use with a retrofit radio with ISO connection.
If you have a FIAT radio fitted ex works, you will also need the following adapter for installation:
- PP-AC16a (please order separately)
Here you can find the installation video for the Jumper Sound Upgrade:
Scope of delivery
- 1x OPTION DSP6
- 1x OPTION Citroen Jumper loudspeaker
- 1x Rock-2 (6.6 kg)
- 1x cable set for plug & play installation incl. cable for power supply
- 1x PP-SUB-2.5-STEREO subwoofer cable
- 1x remover tool
- 1x aluminium butyl insulating mat
- 1x Mounting material
- 1x manual
DSP6 | Ultra compact Class HD DSP amplifier
Two channels are assigned to the front system, while two further channels are available for the rear speakers and a passive subwoofer. Two further channels are then available via the Line Out connection to connect additional active subwoofers or power amplifiers and control them via the DSP.
Technical data DSP6:
- Highly efficient 6-channel DSP amplifier
- Class GD
- 6-channel amplifier / 8-channel DSP
- 6 x 60 watts RMS (4 ohms)
- 4 x 60 watts RMS (4 ohms) + 1 x 120 watts RMS (2 ohms mono mode switchable)
- Channels 5 and 6 are operated in stereo mode for subwoofers
- Minimum impedance on all stereo channels: (3 Ohm)
- Minimum impedance in mono mode: 1.5 Ohm
- ADEP.3 diagnostic protection for easy connection to OEM radios
- Start/stop capable up to 5 sec. up to 6 volts
- High-level in (4 channels) with automatic on/off switch
- Frequency band: 20 Hz to 21k Hz
- Integrated 8-channel DSP processor with 358 kHz
- 2 channels line-out up to 3 Volt | 3.5mm jack
- 2 phase synchronous DC/DC converter
- A/D converter: BurrBrown
- D/A Converter: BurrBrown
- Operating voltage: 10.3 V - 17.5 V
- Power reduction to mid-power mode
- Minimised Dimensions for uncomplicated retrofitting
- 94 x 149 mm x 32 mm (118 x 149 mm with mounting bracket)
- 0.6 mA standby quiescent current
- Main connection: 20-pin Molex MiniFit Jr.
- Subwoofer connection: 4-pole Molex MiniFit Jr.
- Programming port for DSP-Eprom: RJ-45 modular jack
- Remote control connection: RJ-45 modular jack
- Power and Protect LED
Zubehör
Delivery time: 2-3 days ***
free shipping **
Delivery time: 2-3 days ***
free shipping **
Delivery time: 2-3 days ***
free shipping **
Delivery time: 2-3 days ***
free shipping **
Delivery time: 2-3 days ***
free shipping **
Delivery time: 2-3 days ***
free shipping **