Sound system for Citroen Jumper | V1 | DSP power amplifier + subwoofer ROCK-1 | Plug & Play | OPTION
€839.00*
Prices incl. VAT plus shipping costs
Delivery time: 2-3 days ***
free shipping **
Citroen Jumper | Sound system V1 ROCK-1 | Subwoofer, DSP power amplifier | Plug & Play | Option
If you also want to improve the sound in your camper simply but noticeably, have already retrofitted the speakers and now want to take the next step, then this set for your Citroen Jumper with radio preparation ex works is just right.
You can easily and quickly integrate the incredibly compact power amplifier into your camper via plug & play using the cable set included in the scope of delivery and enjoy your sound upgrade in no time at all. The 6-channel power amplifier provides your front system and the Rock-1 subwoofer with sufficient power so that you can now utilise the full potential in terms of sound, bass and level. Due to the digital design, the power amplifier emits hardly any heat and can therefore be installed invisibly in the radio slot.
The passive under-seat subwoofer can be installed in the Citroen Jumper directly and flush under the seat, provided there is no second battery installed.
If you have a factory-fitted radio, you will need an additional one for installation:
Two channels are assigned to the front system, while two further channels are available for the rear speakers and a passive subwoofer. Two further channels are then available via the Line Out connection to connect additional active subwoofers or power amplifiers and control them via the DSP.
If you also want to improve the sound in the mid and treble range, you can go straight for this complete set including front system and plug & play power amplifier: DSP6-DUC-V3
Scope of delivery
- 1x OPTION DSP6
- 1x Rock-1 (4.3 kg)
- 1x cable set for plug & play installation incl. cable for power supply
- 1x PP-SUB-2.5-STEREO
- 1x Mounting material
- 1x manual
DSP6 | Ultra compact Class HD DSP amplifier
The 6-channel power amplifier provides your front system and an optional subwoofer with sufficient power so that you can now utilise the full potential in terms of sound, bass and level. Due to the digital design, the power amplifier emits hardly any heat and can therefore be installed invisibly in the radio slot.
Two channels are assigned to the front system, while two further channels are available for the rear speakers and a passive subwoofer. Two further channels are then available via the Line Out connection to connect additional active subwoofers or power amplifiers and control them via the DSP.
Technical data DSP6:
- Highly efficient 6-channel DSP amplifier
- Class GD
- 6-channel amplifier / 8-channel DSP
- 6 x 60 watts RMS (4 ohms)
- 4 x 60 watts RMS (4 ohms) + 1 x 120 watts RMS (2 ohms mono mode switchable)
- Channels 5 and 6 are used for subwoofers in stereo mode
- Minimum impedance on all stereo channels: (3 Ohm)
- Minimum impedance in mono mode: 1.5 Ohm
- ADEP.3 diagnostic protection for problem-free connection to OEM radios
- Start/stop capable up to 5 sec. up to 6 volts
- High-level in (4 channels) with automatic on/off switch
- Frequency band: 20 Hz to 21k Hz
- Integrated 8-channel DSP processor with 358 kHz
- 2 channels line-out up to 3 Volt | 3.5mm jack
- 2 phase synchronous DC/DC converter
- A/D converter: BurrBrown
- D/A Converter: BurrBrown
- Operating voltage: 10.3 V - 17.5 V
- Power reduction to mid-power mode
- Minimised Dimensions for uncomplicated retrofitting
- 94 x 149 mm x 32 mm (118 x 149 mm with mounting bracket)
- 0.6 mA standby quiescent current
- Main connection: 20-pin Molex MiniFit Jr.
- Subwoofer connection: 4-pole Molex MiniFit Jr.
- Programming port for DSP-Eprom: RJ-45 modular jack
- Remote control connection: RJ-45 modular jack
- Power and Protect LED
Zubehör
Delivery time: 2-3 days ***
free shipping **
Delivery time: 2-3 days ***
free shipping **
Delivery time: 2-3 days ***
free shipping **
Delivery time: 2-3 days ***
free shipping **
Delivery time: 2-3 days ***
free shipping **
Delivery time: 2-3 days ***
free shipping **